Used 1150kW Waukesha Natural Gas Generator

Price (USD): Call +27-72-955-2560 or Request Quote
Item#: USP009052
Wattage: 1,150 kW
Make/Model: Waukesha VHP 7044GSI
Year of Mfr: 2014
Hours: Low Hours
Fuel Type: Natural Gas
Frequency: 60 Hz
Additional Info:

VHP7044GSI – EPA - 1150 KW, 1200 RPM, 60 HZ, 600 / 480 V AC


 1050 KW, 1000 RPM, 50 HZ, 400 VAC

 New – never used – surplus – Warranty expire

 Natural Gas – Propene – Associated Gas, etc

 Only load test hours

New Waukesha 1150 kw Natural Gas Generator

Model VHP 7044GSI, EPA Certified, 1200rpm, 600 / 480 VAC, 3 phases


Weather Enclosure w/skid

 Engine Driven Radiator assembly

 • Engine Controls & Interface: Waukesha Engine ECU & Auxiliary I/O Box

• Kato Alternator, 1200 kw / 1500 kva, 6P6-3300, 6 – Poles, 2 Bearing, 1200 rpm, 80 Deg C temp. Rise (40 Deg. Ambient)

IP-23 Enclosure, PMG, Class “H”, 600/480 volt AC dual Voltage, 3 Ph, 60hz, 0.8 PF.

• Renold Coupling  

• Engine controls and Interface – ECU and auxiliary I/O box

• 50 gallon oil make-up system with level indication

• Inlet gas train with regulator, manual shutoff valve and solenoid – gas train piped to outside of enclosure

• 3 - way exhaust catalyst and industrial exhaust silencer with heat blanket and exhaust flexible connection, Exhaust stack – 4’ extension with rain cap

• Exhaust Supports: Structural frame to support catalyst and silencer from Genset platform

• Engine skid recessed-mounted into working skid - Non-slip diamond plate floor

• Base frame designed to accommodate drop over, weather - proof enclosure Lift - off frame, for (6) - point rig on/lift off from base / platform

•  - Removable lifting eyes

• Bolt-on connection to platform/base

• 2) single access doors

• (1) double access door

• Spill Containment for engine coolant & oil, Incorporated into working platform

• Main Generator Circuit Breaker

o Front access only through double doors on alternator end of Genset

o NEMA 3R rated

o 2000AF insulated case circuit breaker,

o Fixed mounted, 600/480VAC NEMA 3R, 65k AIC, UL891

o LSIG trip, neutral sensor, 24VDC shunt trip, Form ‘C’ aux contacts

o Copper ground bus

o Metering CT’s and PT’s

o CB open & close control by Deep Sea 8610 Controller

• Deep Sea 8610 Engine controller – parallel capable to utility - Gen start/stop/shutdown, sync, island, load share (other Deep Sea Gens)
& utility parallel (adj. base load) modes of operation

• Cable connection, 600/480V, 2000A – Alternator output  Main CB, protected in steel wire way

•Exterior cable connection - Copper bus with NEMA pads/holes designed to accept customer cables and lugs,

Designed for cable entry from ground level, at side of enclosure near double doors

• 480 v to 120/208v transformer

•100 amp load center

• Interior lighting, receptacles, and cable tray - Convenience Receptacles – GFCI, (1) double socket each side of Gen container, (1) near breaker/control cabinet

•DC emergency lighting each side of container, above access/escape doors with timer.

•Exterior lighting – (2) elevated lights to maintain light at ground level, pre-wired and installed but shipped loose

•Light switches with weatherproof covers

•Flush mount emergency stop with break glass NEMA 3R, shipped with extra contact blocks

• Battery charger SENS, Battery Box with spill containment

• Engine start batteries and containment

• 4 hour load test

• Any externally mounted items that must be removed for shipment are to be re-installed by the installing rigger / contractor

Note: Unit was set up for 600 VAC application, customer needs to review and do a small change into the XF1 – Trafo, and review the PT’s – CT’s for his specific application voltage. 


Request Quote    Power Calculators

Equipment is sold as is. EXW warehouse. Subject to prior sale. Shipping quotes available upon request.